The short answer
Many Clinton Hill chimneys have unlined or damaged clay flues that aren't suited to today's boilers, water heaters and inserts. StrongHold Chimney Services inspects the flue, sizes a liner to your appliances and installs it. A new liner is often needed when a building converts its boiler from oil to gas.
Clinton Hill is full of brownstones, rowhouses and pre-war apartment buildings whose masonry chimneys were built long before today's boilers, water heaters and gas inserts. Many of those flues were never lined, or were lined with clay tile that has since cracked, shifted or lost its mortar joints. A properly sized liner gives exhaust a sound, continuous path out of the house. StrongHold Chimney Services installs chimney liners for Clinton Hill homes and buildings from our office in Williamsburg, about 2 miles north. Our certified technicians handle the job from the first inspection through the final check.
Why Clinton Hill Chimneys Often Need a New Liner
Older masonry chimneys in this part of Brooklyn were typically built for coal or wood, then adapted over the decades to oil and later gas. Each change put different demands on the flue. Clay tiles can crack from heat, settle out of alignment, or erode where the joints have washed out. Some chimneys in older rowhouses have no liner at all, only brick.
Gas appliances add a specific problem. Gas exhaust produces acidic condensate, and in an unlined or damaged masonry flue that moisture can corrode mortar and brick over time. That is why the chimney has to be evaluated when a New York City building converts its boiler from oil to gas, and why a new liner is often part of that work.
- Flaking tile, crumbling mortar or debris collecting at the base of the flue
- Water stains, white deposits or damp spots on walls next to the chimney
- A planned boiler conversion, new water heater or new fireplace insert
- Draft problems, such as smoke or fumes spilling into the room
- An inspection that found gaps, cracks or a flue that is the wrong size

Liner Options We Install
The right liner depends on what is venting into the chimney and how the flue is shaped.
Sizing matters as much as material. If a liner is too large, exhaust can cool and condense. If it is too small, it can restrict draft. We size each liner to the appliances connected to it and follow the appliance manufacturer's requirements.
- Stainless steel liners are the most common choice for gas and oil boilers, water heaters and many wood-burning setups. Flexible versions can follow the offsets found in older chimneys.
- Aluminum liners suit some gas appliances, where the manufacturer allows them.
- Cast-in-place liners use a mortar-like material poured around a form inside the flue. They can also help when the existing masonry is in rough shape.
- Clay tile relining is possible in some chimneys, though it usually requires more demolition.
How Installation Works in a Clinton Hill Home
Every job starts with an inspection. Under the NFPA 211 standard, a change to the system, such as a new appliance or a switch of fuel, calls for a Level 2 inspection, which includes a camera look inside the flue. If a hidden hazard can only be reached by opening part of the chimney or building, that becomes a Level 3 inspection.
A typical installation then includes cleaning the flue and removing obstructions or broken tile where needed. We run the liner from the top of the chimney down to the appliance connection, insulate it when the installation calls for it, and seal the top with a cap. Before we leave, we check the draft and the connections.
Rowhouses and brownstones often share party walls and have roof access through a hatch or bulkhead. We plan that access ahead of time and protect interior finishes near the appliance. When the liner is part of a larger project, we coordinate with the building owner, the super or the boiler contractor.
Time for your annual chimney check?
Timing Around Heat Season
New York City's heat season runs from October 1 through May 31. During that period, building owners must keep apartments heated to the city's minimum temperatures. For multi-family buildings, late spring and summer are the easiest times to reline a boiler chimney, because the heating system can be shut down without leaving tenants cold. If a liner problem turns up in mid-winter, we work with owners to keep downtime as short as practical.
After installation, plan on yearly inspections. NFPA 211 calls for chimneys, fireplaces and vents to be inspected once a year, and a new liner is no exception.
Serving Clinton Hill and Nearby Neighborhoods
Our Williamsburg office is about 2 miles from Clinton Hill. We also install liners in Fort Greene, South Williamsburg, Downtown Brooklyn, DUMBO and Williamsburg. Whether you own a single brownstone or manage a pre-war apartment building, we can inspect your chimney, explain what we find and recommend the liner that fits your appliances.
More services in Clinton Hill
- Chimney Sweep in Clinton Hill
- Chimney Inspection in Clinton Hill
- Chimney Repair in Clinton Hill
- Air Duct Cleaning in Clinton Hill

